search

ACT ACTPRO IOM Provozní pokyny Strana 54

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 55
  • Tabulka s obsahem
  • KNIHY
    • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 53
TAMPER
MAINS
PRESENT
+
12V DC
-
NC
C
NO
1 2 3 4 5 6 7 8
On
NETWORK 1
B
A
Shield
ACT4000
A
B
0V
A
B
0V
Total Length max 1.4km
Network cable use either:
(1)Single shielded twisted pair, Belden 9501 or similar.
(2)CAT5 Cable: A/B must use the same twisted pair.
To next Door
or IO Module
DOORS
ACTpro IOM IO Module Installation
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
NC
C
NO
OV
NC
C
NO
NC
C
NO
OV
OP1
OP2
OP3
OP7
OP4 OP8
OP6
OP5
B
TX
A OV
RX
1 2 3 4 5 6 7 8
On
1 2 3 4 5 6 7 8
On
1 2 3 4 5 6 7 8
On
1 2 3 4 5 6 7 8
On
Upto 4 IO Modules maybe connected a single ACT Controller.
The IO Modules share the same network as Door stations (DS100s).
Therefore a controller may support up to 16 Doors and 4 IO Modules.
IO Module Addr 1:
IO Module Addr 2:
IO Module Addr 3:
IO Module Addr 4:
FACTORY DEFAULT
This unit should be reset to its
factory default condition before
installation. To do this, power
the unit up with ALL switches in
the OFF position. The two LED's
will illuminate for about 2 sec.
The correct switch settings may
then be set.
If the Mains Present or Door
Contact inputs are not used,
they should be linked to 0V
LED Functionality:
Red LED indicates the status of communications with the Controller.
While online to the controller the Red LED will flash rapidly.
If there is a problem it will flash slowly (about once a second).
Green LED will flash if an event occurs on the IO Module.
SETTING IO MODULE ADDRESS
IO Module address is set via the DIP
switches. Up to 4 IO Modules maybe
connected to a ACTpro 2000 controller.
4
5
6
8
OV
INPUTS
2
1
3
OV
7
INPUTS:
All 8 inputs may be supervised (enabled from
ACTWin software). Supervised inputs maybe
in one of 4 states, Normal,Active,Short or Open
circuited. Supervised inputs required the installer to
provide 2 resistors per Supervised input as shown
below.
Installation of an IO Module requires the following
(1) Wiring Inputs and Outputs.
(2) Providing 12V Power.
(3) Wiring IO Module A,B and 0V RS485 signals to the Controller.
(4) Setting the IO Module address
All Configuration of Input/Output Operation is performed from ACTwin
A/B/OV RS485 WIRING
0V
IP1
4k7
4k7
49
Zobrazit stránku 53
1 2 ... 49 50 51 52 53 54 55

Komentáře k této Příručce

Žádné komentáře
Související produkty a manuály pro Sériové rozvaděče ACT ACTPRO IOM
Sériové rozvaděče ACT ACT5 PROX Uživatelský manuál   (12 stránky)
Sériové rozvaděče ACT ACT5 PROX Specifikace   (80 stránky)
  • Coopra WorldSpace ARIETE JMR electronic CPI
  • Bushnell ne LG Pračky Radio Shack ne Central Pneumatic Stříkací barva Lenovo Numerické klávesnice
  • Philips Elite 3000K Electrolux FGH50K3 Bertazzoni MAST304INMXE Energizer HDL33A2E Samsung OfficeServ SMT-I5220
  • Ritmix AVR-440 Uživatelský manuál Ge PGP953DETWW Uživatelský manuál Cisco 3032 Uživatelský manuál AEG L7FE74485S Uživatelský manuál Samsung 932GW Uživatelský manuál